About Angela Peck

This author has not yet filled in any details.
So far Angela Peck has created 9 blog entries.

New Mechanical System for Supporting HVAC Equipment

GreenLink has introduced an engineered mechanical support system for mounting a wide range of HVAC equipment including AC units, mini splits, heat pumps, condensers, and associated pipelines and conduit.  The system is designed to produce an extremely secure installation, especially in the face of high winds and seismic events. It is available as a kit [...]

By |2020-11-02T13:37:03-05:00November 2nd, 2020|Engineering, HVAC, Support, Wind Uplift|Comments Off on New Mechanical System for Supporting HVAC Equipment

The toxic top:  The environmental and structural risks of treated lumber supports on rooftops.

The market has been shifting away from treated wood blocks for rooftop support of pipes, HVAC equipment, and ductwork, etc., largely because they are subject to biodegradation—in other words, rot.  When the sleepers deteriorate, they cause pipe sag and unbalanced HVAC equipment which shortens operational life.  But there are other issues—critical ones---for moving toward other [...]

By |2020-11-02T13:44:58-05:00November 2nd, 2020|Knuckleheads, Nylon, Roofing Materials|Comments Off on The toxic top:  The environmental and structural risks of treated lumber supports on rooftops.

The origin of the KnuckleHead Name

The first KnuckleHead At the turn of the century, it became evident that woodblocks, bricks and other improvised supports for rooftop equipment were no longer sustainable. The first engineered support system was designed by Dr. Tibor Keller, a master machinist. This component was capable of lifting and holding light pipes such as conduit, gas pipes [...]

By |2020-11-02T13:24:10-05:00November 2nd, 2020|Engineering, Knuckleheads, Support, Uncategorized, Wood Blocks|Comments Off on The origin of the KnuckleHead Name

Securing HVAC Equipment on Mod-Bit Roofs without Mechanical Fastening

Modified bitumen roofs continue to maintain a significant share of the domestic market.  Mod bit is often described as “rubberized” asphalt, meaning it consists of asphalt and a polystyrene or polypropylene polymer infused into a reinforcing fabric.  It is applied in 4’ squares as a two-ply system: first a base sheet, then a top sheet [...]

By |2020-11-02T13:07:38-05:00November 2nd, 2020|HVAC, Knuckleheads, Roofing Materials, Support, Uncategorized|Comments Off on Securing HVAC Equipment on Mod-Bit Roofs without Mechanical Fastening

Tall VRFs/Mini-Splits: Blowing in the Wind? Here’s an Answer.

Mini splits are becoming increasingly popular on commercial buildings as well as residential housing. Usually, they can be mounted on any number of support systems, but the taller, narrower profile of the larger units creates a level of vulnerability. In windy conditions, it can tip over, even if mounted. The greater surface area of the [...]

By |2020-11-02T12:35:05-05:00November 2nd, 2020|Engineering, HVAC, Knuckleheads, Roofing Materials, Uncategorized, Wind Uplift, Wood Blocks|Comments Off on Tall VRFs/Mini-Splits: Blowing in the Wind? Here’s an Answer.

Case Study: A Public School in Michigan

Clearing the Way for Coating A public school roof in central Michigan, was scheduled to be resealed with a liquid applied coating.  Two adjacent roof sections were involved separated by a parapet wall over which line sets needed to pass.   Prior to coating  five mini splits using 4”X 6” wood sleepers were mechanically fastened to [...]

By |2020-11-02T12:07:02-05:00November 2nd, 2020|HVAC, Knuckleheads, Nylon, Roofing Materials, Uncategorized, Wind Uplift|Comments Off on Case Study: A Public School in Michigan

Rough-Ride for Roof Mounted Equipment

Field reports from HVAC and roofing contractors indicate an increasing issue relating to the stability of rooftop equipment installations.  Earthquakes at 6.4 magnitude in January ran through the Caribbean wreaking havoc with the electrical grid and power lines, not to mention rooftop-mounted equipment.  Elsewhere, high winds and violent storms have caused the same.  As the [...]

By |2020-01-27T21:05:31-05:00January 27th, 2020|HVAC, Knuckleheads, Nylon, Roofing Materials, Support, Wind Uplift, Wood Blocks|Comments Off on Rough-Ride for Roof Mounted Equipment

KnuckleHeads and Hurricanes

Recently Green Link principals, Phil Georgeau, Founder, and Lisa Mulder, Technical Director traveled to San Juan, Puerto Rico to survey the destruction caused by Hurricane Maria, and to study how the use of the KnuckleHead support system could provide more stable rooftop installations in the face of future hurricanes. Hurricane Maria, which struck in [...]

By |2019-07-29T14:28:11-05:00July 2nd, 2019|HVAC, Knuckleheads, Nylon, Support, Uncategorized, Wind Uplift, Wood Blocks|Comments Off on KnuckleHeads and Hurricanes

How To: Build a Custom KnuckleHead Extension

FOUR STEPS TO MAKE A KnuckleHead EXTENSION* KnuckleHead Extensions should be used with our product to elevate equipment and pipes above the adjustable height range of a base model KnuckleHead.  Green Link provides extensions of 8, 12, and 18 inches. If you want to make your own size extension the following are the steps to [...]

By |2019-07-29T14:25:49-05:00May 17th, 2019|extension, HVAC, Knuckleheads, Roofing Materials, Support|Comments Off on How To: Build a Custom KnuckleHead Extension
Go to Top